RS/6000 SP 9076 SMP System and Service Processor Firmware Update (ECA N/A)

Applies to: IBM RS/6000 SP 9076-5X0 332Mhz SMP Thin/Wide Nodes

If you experience problems or have questions regarding any component of this document or the installation of the code please call 1-800-IBM-SERV for assistance.

Please read this document in it's entirety and in particular understand the Notes and Cautions section before applying this F/W to any node.

Contents:

1.0 Machines/Nodes Affected

2.0 Revision History

3.0 Related Publications

4.0 Cautions and Important Notes

5.0 Downloading and Unpacking the Firmware Update Package

6.0 Putting the Firmware on the System

7.0 Validating the Checksum

8.0 Setting up the Distributed Shell

9.0 Determining Your Current Firmware Levels

10.0 Updating the Firmware on the Target Nodes
 
 


1.0 Machine/Nodes affected

This update provides new System and Service Processor (SvP) firmware (FW) on RS/6000 SP 9076 332MHZ Thin/Wide Nodes.  This firmware can be applied to a 332Mhz Thin/Wide node (FC 2050/2051) operating on any model of 9076 that has an operating system of AIX at 4.2.1 or greater.

The latest levels are:

  • System Firmware: WIL08295  (Replaces WIL05292)
  • Service Processor Firmware: wc010611  (Remains The Same)

NOTE:
The System and Service Processor Firmware for the 332Mhz node consists of two seperate files, as indicated above.


2.0 Revision History

System FW
 

Level

Description

L08295

  • Corrects E140 Hang Defect

L05292

  • Corrected a problem that caused the ping test in the system managment services (SMS) menu to fail when run on the integrated ethernet adapter and the 10/100 Ethernet Adapter (FC 2968).
  • Corrected a problem that was causing the memory DIMM VPD to be formatted incorrectly; this prevented the DIMM VPD from being displayed by the command "lscfg" in AIX version 5.3.
  • Added support for ARP (address request protocol).

 

L04197

  • Added support for AIX 5.3.
  • Added boot support for mksysb created on optical media in Universal Data Format.
  • Corrects intermittent problems with valid  system bootlist being ignored on systems with level L03115 or L03273 installed when bootlist is altered via graphics display being used as the system console.
  • Added support to provide response to APR requests for Hot Standby Router Protocol (HSRP) or other network processes that generate ARP requests during NIM operations.

L03323

  • Corrects error 20EE000B with firmware WIL03273 level.

L03273

  • Corrected ping failure on nim boot with error 20A80001.
  • Fixed F/C2969 Ethernet not pinging when connected to router.
  • Corrected boot failure after upgrading to WIL03115 firmware.

L03115

  • Corrected Auto configuration, ping and NIM failures on Ethernet adapters attached to switch or router with  spanning tree algorithm enabled.
  • Corrected boot failure with checkpoint E1F6 displayed after bootlist is set via AIX and more than 5 devices are specified.
  • Corrected missing devices in SMS bootlist when bootlist set via AIX.
  • Parameter change to limit bootlist entries set via AIX to 5.
  • Corrected boot failure with 'Default Catch' message displayed on console when booting from tape media containing large boot image.
  • Corrected error 20EE000B: unable to find boot record after restore on NIM install on 36GB or larger disks.
  • Corrected 'Default Catch' message displayed on console after SMS 'Change SCSI ID' utility screen is accessed.

WIL02113

  • Added support for 4-Port 10/100 Ethernet (FC4961, A-E)
  • Enhanced support for MX2 (FC4026, 6-M)
  • Corrected problem with speed and media type settings on multiple Ethernet adapter types during NIM install
  • Eliminated need to zero out gateway address field if Client and Server on same subnet during NIM install
  • Corrected SMS bootlist menu for missing header 
  • Corrected problem with failing Ping tests across gateways
  • Corrected problem with SMS utilities menu after executing Ping test with all Token Ring adapters

WIL01337

  • Added menus in FW for Ethernet  (FC4962, A-F) 
  • Added support for MX2 (FC4026, 6-M)
  • Corrects NIM boot failure from foreign packets
  • Enhanced defect isolation for NIM install/boot interrupt
  • Added UDF driver to support DVD media type

WIL01269

  • Added support for Fiber Channel / Boot enhancdements
  • Fix for tty overrun and reduce MPIC
  • Removed checking for PCI vendor ID and PCI  device ID

WIL01159

  • Multiple NIM install fixes for Gigabit Fiber (FC2969, Type 9-U) and Gigabit UTP (FC2975, Type A-A) Ethernet adapters
  • Miscellaneous Serviceability / Maintenance fixes

WIL00278

  • Support for 10/100/1000 BaseT Ethernet Adapter (FC 2975)
  • Improved memory failure isolation for SRN 651-619
  • Miscellaneous Serviceability/Maintenance fixes

WIL00125

  • Corrects incorrect location codes
  • Support for IBM 4-Port Base TX Ethernet PCI Adapter
  • Misc fixes for SMS menu problems
  • Add network boot related fixes

WIL99308

  • Added boot support for the Dual Ultra2 SCSI(4-R) Adapter, FC - 6205

 

SvP FW

Level

Description

wc010611

  • Enhancements to  SvP menu

wc000901

  • Miscellaneous Mfg. enhancements

wc991027

  • Adds miscellaneous mfg related fixes

wc990831

  • Adds NVRAM clear/ Checkstop analysis to menus
  • Potentially fixes once-a-minute sysplanar0 errors

3.0 Related Publications

You may have to refer to the following publications during this install:

  • GA22-7330 IBM RS/6000 SP 332 MHZ Thin and Wide Node Service Guide.
  • GC23-3897 IBM RISC System/6000 Scalable POWERparallel Systems Administration Guide.
  • GC23-3900 IBM RISC System/6000 Scalable POWERparallel Systems Command and Technical Reference.

4.0 Cautions and Important Notes

INSTALLATION OF THIS CODE WILL CAUSE AN UNCONDITIONAL REBOOT OF AIX AND IS NOT CONCURRENT WITH CUSTOMER OPERATIONS.

Never power off the node during the update process

DO NOT Use The SvP Firmware AGyymmdd Version

Ensure that the new Service Processor firmware is a "WC" version such as WC980413 (98=year, 04=month, 13=day). DO NOT use the SvP firmware AGyymmdd version because the "AG" version is for the 7026-H50 systems. If you update SP 9076 332MHZ nodes with "AG" version, it will corrupt the SvP firmware. The server will show E212 or E213 then shut itself off. Replacing the SvP card is the only recovery solution for the field.
 

How To Determine Release Date From The File Name

Date and level identifiers for the SvP FW uses the 8-digit Gregorian date code method in terms of year, month, and day (such as 19980413 for WC980413 level). The System FW uses the 5-digit Julian date code method in terms of day number in a year (such as 98112 for WIL98112 level -- 112th day of 1998 or April 22, 1998).
The Combo FW uses the Gregorian date code.
 

The SvP and System Firmware need to be at companion levels

When an I/O planar or a Service Processor (SvP) card is replaced, the System firmware on the new I/O planar and the SvP firmware on the new SvP card must be checked to ensure that they are at the latest level, or that they are at companion levels. If they are not, it is recommended that both the System Firmware and SvP Firmware be "re-flashed" to the latest level or at the very least to the correct companion level. Companion levels are those files that have the same release date as indicated in the table below.
 

Installation Time

The typical time to install this microcode on one node is 1.0 hr. This firmware can be installed on more than one node at a time but the total install time will vary depending on how many nodes/frames are involved with the upgrade. The microcode does not become active when installed and requires a system reboot to become active. This reboot  time will vary depending on the system and the amount  of features installed.
 
 
 
 


5.0 Downloading and Unpacking the Firmware Update Package
Instructions for downloading and unpacking the firmware update package follow.

5.1 CD-Rom Package
Follow instructions in the CD-ROM ReadMe for:

  • MDS (Microcode Discovery Service)/Inventory Scout
  • Required AIX levels
  • Manual Copy Microcode Files

a) The AIX command to mount this CD-ROM is:
     mount -v cdrfs -r /dev/cd0 /mnt
     cd /mnt

Note: Don't forget to unmount the /mnt directory after Section 10.0 Updating Firmware on Target Nodes

Enter:
cd (to get out of /mnt directory)
umount /mnt
 

b) Provide a directory on an AIX system to receive the AIX format file.

      Enter:
        mkdir /tmp/fwupdate

         Note: If the directory /tmp/fwupdate already exists,
           make sure it is empty before proceeding.

c) Manually copy WIL08295.img and wc010611.img to /tmp/fwupdate directory
    This can be found in the /microcode directory under 90765X0 on the CD-ROM
 

Proceed to Section 7.0,Validating The Checksum.
 

5.2 Internet Package
The firmware, in AIX and DOS formats, are located at the web site

          http://techsupport.services.ibm.com/server/mdownload2/download.html

Follow the instructions on this web page. You must read and agree to the license agreement to obtain the password (case sensitive) for unpacking the firmware packages.

In the table for System Microcode, scroll down to the entry for 9076 332MHZ SMP T/W .

The download choices at that entry are:

  •  Description (Instructions document)
  •  AIX Format (For downloading to an AIX server or system)
  •  DOS Format (For downloading to a DOS or Windows workstation)

You will want a copy of the description (instructions document) and one of the format choices. You may transfer files to the target system in one of several ways.

  • By downloading files directly to the target system.
  • By downloading files to an intermediate AIX system and then using either ftp or diskettes for transferring to the target server.
  • By downloading files to an intermediate AIX system and then using either ftp or diskettes for transferring to the target server.

Detailed download/unpacking instructions follow for each of the downloading preferences.

  •  If using an AIX system for downloading, continue to paragraph 5.3
  •  If using a DOS or Windows workstation for downloading, skip to paragraph 5.6

5.3 Downloading the AIX Format File
Use this method to download to an AIX system.
 

Note: In the instructions that follow are specific AIX commands.
           AIX commands are CASE (lower and upper) SENSITIVE, and must be entered exactly as
           shown, including the filenames.
 
 
 

  a) Provide a directory on an AIX system to receive the AIX format file.

      Enter:
        mkdir /tmp/fwupdate

         Note: If the directory /tmp/fwupdate already exists,
           make sure it is empty before proceeding.

  b) Transfer the AIX format file to the /tmp/fwupdate directory (using "Save as ...").
       You'll see that the filename is 90765X0F.BIN

  c) Unpack the file by executing the instructions below.
       You will be need the password from the license agreement.

Enter the commands:

        cd /tmp/fwupdate
        chmod +x 90765X0F.BIN
        ./90765X0F.BIN

     [Don't overlook the periods (.) in the above command.]

 These files will be added to  /tmp/fwupdate:

      WIL08295.IMG
      wc010611.img
      ReadMe.TXT

If you used the above procedure to transfer the AIX format file directly to the target server,  proceed to Section 7.0,Validating the Checksum.

Otherwise, from the intermediate AIX system, choose one of the following methods for transferring files to  the target server.

To transfer files to the target server via the ftp method, continue to paragraph 5.4
To transfer files to the target server via the diskettes method, skip to paragraph 5.5

5.4 The FTP Transfer Method
This method presumes you have ftp access to the target server.

On the intermediate AIX system,

   Enter the commands:
      ftp {name of target server}
     {Login with a valid userid and password}

      bin
     lcd /tmp/fwupdate
     mkdir /tmp/fwupdate
     cd /tmp/fwupdate
     put WIL08295.IMG
     quit

Proceed to Section 7.0,Validating the Checksum.

5.5 The Diskette Transfer Method

This method can be used for cases in which electronic connections between the intermediate AIX system and the target server are inconvenient.

 Two 2MB (HD) new or freshly formatted diskettes are required.

 With a diskette loaded in the drive,
  Enter the commands (this process will request additional diskettes as each is filled):

       cd /tmp/fwupdate
       ls *.img | backup -i -v -f/dev/rfd0

This will produce AIX backup diskettes.  Label these diskettes, respectively,

     "Volume 1:  FW (WIL08295) for 9076-550"
     "Volume 2:  FW (wc010611) for 9076-550"

Proceed to Section 6.0,Updating the Firmware.

5.6 Downloading the DOS Format File
Use this file to download to a DOS or Windows workstation.

  a) Prepare a directory for receiving the DOS format file.
      This directory can be in any partition with 12MB available space.
      Executing in such a partition, called [path] in these instructions
      (ex. c:\download),

      Enter:
       md [path]\fwupdate

     Note:  If the directory [path]\fwupdate already exists,
                 make sure it is empty before proceeding.

     b) Transfer the DOS format file to the [path]\fwupdate directory (using "Save as ...").
         You'll see the filename is 90765X0F.EXE

     c) Unpack the file by executing the instructions below.
         You will need the password from the license agreement.

        Enter the commands:
        cd [path]\fwupdate
        90765X0F

These files will be added to the fwupdate subdirectory:

       L08295.EXE
       wc010611.IMG
       WIL8295.IMG

       readme.txt

5.7 Diskettes for Firmware Updates

One 2MB (HD) new or freshly formatted DOS diskette is required.

  Note: The diskettes produced below will be in a format that can be used
             directly with a computer running AIX as it's operating system. These
             diskettes, once made on a PC platform, cannot be read using normal PC
             platform tools or command line operations.

  a) With a diskette loaded in the drive,

         Enter the commands:

            cd [path]\fwupdate
          L08295.EXE

      Label this diskette,
           "Volume 1: FW (WIL08295) for 9076-550"
 
 

 



6.0 Putting the Firmware on the System

On the 9076 CWS that you are going to use this firmware, insert the diskette in the floppy diskette reader (rfd0) on the CWS.

Login as root on the Control Workstation (CWS).

Login root

Enter the commands:

mkdir /tmp/fwupdate
cd /tmp/fwupdate
restore

This will put the firmware files into the /tmp/fwupdate directory.
 
 



7.0 Validating the Checksum

Checksums can be used to verify the FW files you received have not been corrupted or altered during transmission. To calculate the checksum, enter:

sum [FW filename]

The checksum is the first number of the output.  Compare the number you get with the previous table.  If the numbers match then you can be sure the firmware files are not corrupted.  Do this for both the system and service processor firmware.
 

 

SYSTEM FIRMWARE

SvP FIRMWARE

RELEASE DATE

Filename

Size

Chksum

Filename

Size

Chksum

Nov 2008

WIL08295.img

1048576

31641

wc010611.img

370800

21507

Nov 2005

WIL05292.img

1048576

31003

wc010611.img

370800

21507

Sept 2003

WIL04197.img

1048576

15953

wc010611.img

370800

21507

Dec 2003

WIL03323.img

1048576

54524

wc010611.img

370800

21507

Sep 2003

WIL03273.img

1048576

41606

wc010611.img

370800

21507

Apr 2003

WIL03115.img

1048576

09107 

wc010611.img

370800

21507

Jul  2002

WIL02113.img

1048576

63736

wc010611.img

370800

21507

Jan 2002

WIL01337.img

1048576

18006

wc010611.img

370800

21507

Nov 2001

WIL01269.img

1048576

41611

wc010611.img

370800

21507

Aug 2001

WIL01159.img

1048576

15085

wc010611.img

370800

21507

Nov 2000

WIL00278.img

1048576

06894

wc000901.img

371056

24934

May 2000

WIL00125.img

1048576

34781

wc991027.img

371056

18658

DEC 1999

WIL99308.img

1048576

56934

wc990831.img

371048

11591

OCT 1999

WIL99287.img

1048576

57737

wc990831.img

371048

11591


 


8.0 Setting up the Distributed Shell

On an SP, you need to perform on each node what would normally be done on a standalone RS/6000 server.  To install the firmware you must distribute the code to all of the applicable nodes, then install it there.  You must be logged on as root to properly do the install.

All the following commands shown will be run from a window on the CWS. It should not be necessary to telnet or rlogin to the individual SP nodes. You should be familiar with the "dsh" and "pcp" commands. If not, refer to the (GC23-3897) IBM Parallel System Support Program for AIX: Administration Guide or (GC23-3900) IBM Parallel System Support Program for AIX: Command and Technical Reference.

  1. Verify all the target nodes are powered ON and quiesced (ie. No user applications or activity should be allowed).
  1. You will need to create a list of what nodes to install the code on.  To do this type the following command:

  splstdata -G -n

You should see something similar to the following:

                  List Node Configuration Information

node#   frame#   slot#   slots    initial_hostname    reliable_hostname    dcehostname
      default_route     processor_type   processors_installed   description
------------------------------------------------------------------------------
    1        1       1       2    vion01.pok.ibm     vion01.pok.ibm    ""
        9.114.201.190               MP                      1   332_MHz_SMP_Wide
    3        1       3       2    vion03.pok.ibm     vion03.pok.ibm    ""
        9.114.201.190               MP                      2   332_MHz_SMP_Wide

The output will include every node in your system.  For each node that has 332_MHz_SMP in its description, record the first part of the initial_hostname field.  In this case since the initial_hostname is vion01.pok.ibm, you would record vion01.  This will become your list of nodes to be installed with the code.

  1. Next, prepare a Working Collective file to permit you to use the "dsh" and "pcp" commands to install all of the applicable nodes in parallel. Next you will need to put the list of nodenames you just created into a file and export it.  To do this enter the following commands:

            cat > group1
            [nodename1]
            [nodename2]
            [nodename3]
            .
            .
            .
     press Ctrl D
            export WCOLL=/tmp/fwupdate/group1

  1. Test this file to ensure it is working the way you expect by typing:

  dsh date

You should get back a list that looks something like:

            nodename1: Wed Apr 10 10:37:46 EDT 1996
            nodename2: Wed Apr 10 10:37:46 EDT 1996
            nodename3: Wed Apr 10 10:37:47 EDT 1996
            nodename4: Wed Apr 10 10:37:48 EDT 1996

If this output does not contain all the nodes that you expected, examine your node list file /tmp/fwupdate/group1 and also ensure that the Kerberos ticket is current to permit "dsh" to be performed. You may need to refresh the Kerberos. Refer to the SP Administration Guide (GC23-3897) for further help. The System Administrator should also be able to help you with Kerberos initialization. Otherwise, consult your support center.
 
 


9.0 Determining Your Current Firmware Levels

To check the System Firmware level enter:

          dsh "lscfg -vp | grep -p 'System Firmware'"

This command will produce a system configuration report containing sections similar to the following for each node:

System Firmware:
ROM Level (alterable)…......Lxxxxx <==System FW level
Version…..........................RS6K
System Info Specific.(YL)…P2

The ROM Level (alterable) lines list the level numbers of your currently installed System Firmware. If the five right most characters of the update level are less than the latest level than you MUST install the update.

To check the Service Processor Firmware level enter:

                     dsh "lscfg -vp | grep -p 'Service Processor"

           This command will produce a system configuration report containing sections similar to the following for each node:

Service Processor:
Part Number.........................93H4228
EC Level..............................E76324A
FRU Number........................93H4214
Manufacture ID.....................3966-1944843
ROM Level.(non-alterable).....wcxxxxxx
Serial Number.....................00001821
ROM Level (alterable)..........wcxxxxxx <== SvP FW level

The ROM Level (alterable) lines list the level numbers of your currently installed Service Processor Firmware. If the six right most characters of the update level are less than the latest level you MUST install the update.



10.0 Updating the Firmware on the Target Nodes

This section describes the method for transferring the new firmware into the target nodes. Each flash update should complete within one minute.

WARNING:  DO NOT POWER OFF THE TARGET SERVER AT ANY TIME BEFORE THE FLASH PROCESS COMPLETES.

WARNING:  BE SURE THE SYSTEM IS QUIESCED AND NOT RUNNING ANY USER APPLICATIONS.
 

  1. Use "pcp" (parallel copy) to copy the firmware files to each of the target nodes (defined by the Working Collective from above).

            hostlist | pcp -w - /tmp/fwupdate/[System Firmware Filename]  /var
            hostlist | pcp -w - /tmp/fwupdate/[Service Processor Firmware Filename]  /var

        NOTE:  This Will copy the firmware images to the /var directory. Any other directory besides /var will not work.

  1. You may wish to verify the firmware copied over correctly. Perform the following command and verify the firmware files are found on each target node.

            dsh "ls /var/*.img"

  1. You must have root authority on the CWS to update its nodes. This method uses the AIX "shutdown" command, and it assumes the firmware update images are located in the /var directory according to the instructions in this document.  To help ensure file system integrity enter:

            dsh "sync;sync;sync;sync"

  1. Update both the System firmware and Service Processor firmware. You MUST update the System firmware first.

            dsh "/usr/sbin/shutdown -Fu /var/[System Firmware Filename]"
           dsh "/usr/sbin/shutdown -Fu /var/[Service Processor Firmware Filename]"

           The node will power down and reboot to the AIX login prompt.

  1. Remove all old .img files from the /var directories.

            dsh "rm /var/*.img"

  1. Remove all temp files.

            rm -r /tmp/fwupdate

Verify that everything was installed properly.  Use section 9.0 Determining Your Current Firmware Levels to do this.