Readme for IBM Flex System FC 5054 4-port 16Gb FC Adapter

08/15/2013: See Document Change History for details on changes to this document.

Contents


1.0 Overview

This update contains the AIX RPM file for the current level of microcode for the IBM Flex System FC 5054 4-port 16Gb FC Adapter, Feature Code EC2E. This is a multiport adapter with a single ASIC. To update the microcode for the entire adapter, only a single resource (port) need to be updated to ensure the card is updated.

 Back to Contents


2.0 Adapters Affected

This microcode is for feature code EC2E: PN 95Y2393: CCIN 2B77

To determine the part number of the adapter on an AIX system, on the command line key the following command:

lscfg -vl fcsX         

where fcsX represents the adapter. 

Affected adapters will be listed as: FC 5054 4-port 16Gb FC Adapter (df1000e2df1082e2)

 

To determine the presence of this adapter on a Linux system, on the command line key in:

ls /sys/class/fc_host

Example output:   host1  host2

 

Next determine the model description and name for each host. For each host{n} displayed in previous command, on the command line key in the following command,where host{n} is replaced by one of hosts listed in previous step:

 

cat /sys/class/scsi_host/host{n}/model*

 

Affected adapters will be listed as:   

   FC 5054 4-port 16Gb FC Adapter

  

 

The typical time to install the microcode is 0.4 hr.

 Back to Contents


3.0 Microcode Description and Revision History

Microcode Level

Changes

00001000010004300011

This is the level of microcode that is initially supported when it became generally available.

The Firmware Levels Below Are No Longer Supported
Please Update To The Latest Level At Your Earliest Convenience

 

 

 

 

Back to Contents


4.0 Cautions and Important Notes

  • Concurrent Download

The microcode installation does NOT support concurrent download while the fcs resources are available for use. If the fcs resources are in use, they must manually be released prior to starting the download. Failure to do so will result in a message instructing that the fcs resource be freed.

NOTE: It is recommended that the installation be scheduled during a maintenance window or during non-peak production periods.

  • NOTICE FOR AIX CUSTOMERS INSTALLING 00001000010004300011  MICROCODE
    • AIX Requirements
      Prior to installing the microcode, it is required that the following AIX Service Packs or later be installed.
      • AIX 6.1 TL6 SP8
      • AIX 6.1 TL7 SP3 + APAR IV14283
      • AIX 7.1 TL0 SP6
      • AIX 7.1 TL1 SP3 + APAR IV14284

The Service Packs can be obtained from the IBM Fix Central website located at http://www.ibm.com/eserver/support/fixes.

    • VIOS Requirements
      If the adapter is running in a partition running VIOS, it is required that VIOS 2.2.1.4 or later be installed.

 

    • Linux Requirements

RHEL 5.7, RHEL 6.2, and SLES11 SP2 or later are supported.

Back to Contents


5.0 To Determine Adapter Microcode Levels

Before installing the microcode, it is important to determine the current microcode level of the adapter.

5.1 AIX Systems

1.  List the Fibre Channel (FC) adapters installed in the system by typing on the command line:

lsdev-C | grep fcsX

Note the device names of all the fibre channel adapters installed. The adapter device names will be fcsX, where X is 0,1, or some other number. There will be an fcsX listing for each port of the FC EC2E adapter

2.  Determine the current microcode level on the adapter by typing on the command line:

lsmcode-d fcsX
where X is the number of the adapter's port returned from the "lsdev" command above.

A screen similar to the following will be displayed:

DISPLAY MICROCODE LEVEL                                                          802111

fcs0             FC 5054 4-port 16Gb FC Adapter  (df1000e2df1082e2)

 

The current microcode level for fcs0

is 00001000010004300011

 

Use Enter to continue.



F3=Cancel             F10=Exit             Enter

 

If the current microcode level is not 00001000010004300011, then the microcode image on the adapter is not at the latest level.

Back to Contents

5.2 Linux Systems

1.  Identify fibre channel hosts. Following command will list fibre channel hosts.

ls /sys/class/fc_host

 

Example output: host3 host4

 

2. Verify firmware version running on the host.  The following command will display the firmware version loaded by the adapter, where host{n} is replaced by one of hosts listed in previous step.

cat /sys/class/scsi_host/host{n}/fw_version

 

Expected output: 5.06.05 (nnnn)   (nnnn) can be ignored

If version reported is not greater than or equal to 5.06.05, then the microcode image on the adapter is not at the latest level.

Back to Contents


6.0 Install RPM Package

6.1 AIX RPM Package

Use this method to install the AIX RPM package on an AIX system. Note that the commands are case sensitive and must be entered exactly as shown, including file names. Installing the RPM places the binary file df1000e2df1082e2.00001000010004300011  in the /etc/microcode directory.

1. If the /etc/microcode directory does not exist, make a directory to receive the RPM format file. On the command line type:

mkdir /etc/microcode

2. Transfer the RPM format file, df1000e2df1082e2.00001000010004300011.aix.rpm to any temporary directory on the target system.

3. Unpack the file. On the command line type:

rpm -ihv --ignoreos df1000e2df1082e2.00001000010004300011.aix.rpm

4. If the microcode package unpacks successfully, the microcode file will be added to the /etc/microcode directory.

If a message is received saying the "package <package_name> is already installed", you will need to uninstall the rpm package. On the command line type:

rpm -e <package_name>

where <package_name> is the name of the package that was returned in the message. Return to step 3 and attempt to unpack the file again.

5. Go to section 7.0 to complete the update.

Back to Contents


7.0 Installing the Adapter's Microcode

7.1 Using the AIX Command-Line Method

Login as root user. From the command line key in:

diag -d fcsX -T download
where fcsX is the port you on which you want to install the microcode.

Self-explanatory menus will step you through the microcode installation.
Repeat this command for all of the adapters/ports.

Back to Contents

7.2 Using the Diagnostic Service Aid Method

Login as root user.
From the command line key in:  diag
Select:  Task Selection (Diagnostics, Advanced Diagnostics, Service Aids, etc.)
Select:  Microcode Tasks
Select:  Download Latest Available Microcode
Select:  file system
          /etc/microcode
Select the device:  fcs*

Press enter when prompted to download the microcode.
Only one of the fcs resources needs to be updated for the entire adapter to be updated.

Upon completion, a message will state that the microcode has been successfully downloaded and that
the new level is 00001000010004300011.

Back to Contents

 

7.3 Enabling Linux driver firmware load from flash

On RHEL6 and SLES11 Linux distributions, the firmware is loaded automatically by the qla2xxx driver  from the /lib/firmware/ directory. On RHEL5 the firmware is loaded by the qla2xxx driver from the driver image itself. If Standalone Diagnostics are used to update the adapter flash, then 

the qla2xxx driver must be set to load the firmware from the flash by specifying  qla2xxx driver parameter, ql2xfwloadbin. 

 

The steps required to set the ql2xfwloadbin driver parameter in a persistent manner varies by Linux release as described next.

 

RHEL5

 1) Using a Linux text editor, edit the file /etc/modprobe.conf

 2a) If there is a line in the file starting with options qla2xxx then add ql2xfwloadbin=1   to the end of that line.

 2b) If there is no line in the file starting with options qla2xxx then add a new line to the file, options qla2xxx ql2xfwloadbin=1

 3) Save the file

 4) Make a new initrd to include the updated qla2xxx driver options in the boot image.  On the command line, key in

    mkinitrd -f /boot/initrd-$(uname -r).img $(uname -r)

 5) Reboot

 

 

RHEL6

1) Using an a Linux text editor, create a new file /etc/modprobe.d/qla2xxx.conf

2) Add this line to the /etc/modprobe.d/qla2xxx.conf file created in step 1,  options qla2xxx ql2xfwloadbin=1

3) Save the file

4) Save the file

 4) Make a new initramfs to include the updated qla2xxx driver options in the boot image.  On the command line, key in

    dracut -f /boot/initramfs-$(uname -r).img $(uname -r)

 5) Reboot

 

 

 

SLES11 mkinitrd

1) Using a Linux text editor, edit the file /etc/modprobe.local.conf

 2a) If there is a line in the file starting with options qla2xxx then add ql2xfwloadbin=1  to the end of that line.

 2b) If there is no line in the file starting with options qla2xxx then add a new line to the file, options qla2xxx ql2xfwloadbin=1

 3) Save the file

 4) Make a new initrd to include the updated qla2xxx driver options in the boot image.  On the command line, key in

      mkinitrd

 5) Reboot

 

Back to Contents

 

7.4 Using the Standalone Diagnostics CD

Below are references and the general flow on how to update microcode update via CD. This method requires

1) Boot the system via a Standalone Diagnostic's CD

a) To create a bootable Diagnostic's CD go to the following URL.

http://www.software.ibm.com/webapp/set2/sas/f/diags/home.html

b) After booting to Standalone Diagnostics, the Diagnostic's CD can be removed.

2) The Diagnostic's CD should be replaced by a CD containing the unpacked microcode image(s).

The CD containing the microcode images should be prepared prior. This can be done by taking the df1000e2df1082e2.00001000010004300011.aix.rpm file(s) and unpacking them on a usable server. The unpacked files can then be burned on to the CD media.

Back to Contents

 


8.0 Verifying the Update

8.1 Verifying the Update on AIX

1.  List the Fibre Channel (FC) adapters installed in the system by typing on the command line:

lsdev-C | grep fcsX

Note the device names of all the fibre channel adapters installed. The adapter device names will be fcsX, where X is 0,1, or some other number. There will be an fcsX listing for each port of the FC EC2E adapter

2.  Determine the current microcode level on the adapter by typing on the command line:

lsmcode-d fcsX
where X is the number of the adapter's port returned from the "lsdev" command above.

A screen similar to the following will be displayed:

DISPLAY MICROCODE LEVEL                                                          802111

fcs0             FC 5054 4-port 16Gb FC Adapter (df1000e2df1082e2)

 

The current microcode level for fcs0

is 00001000010004300011

 

Use Enter to continue.



F3=Cancel             F10=Exit             Enter

 

If the current microcode level is 00001000010004300011, then the microcode image was updated successfully.

 

Back to Contents

 

8.2 Verifying the Update on Linux

1.  Identify fibre channel hosts. Following command will list fibre channel hosts.

ls /sys/class/fc_host

 

Example output: host1 host2

 

 

2. Verify firmware version running on the host.  The following command will display the firmware version loaded by the adapter, where host{n} is replaced by one of hosts listed in previous step.

cat /sys/class/scsi_host/host{n}/fw_version

 

If version reported is not as expected, carefully retrace steps to confirm each step is completed without error. 

 

 Back to Contents



Document Change History

Date

Change

08/15/2013

Initial Document

 Back to Contents



Apendix: Vendor Firmware Notice

 
 
 

Privacy | Legal | Contact IBM